Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 46 / 364

Initial commissioning of device

Product manual 2CKA001473B5342

│

4. The notification center opens.

– The panel must be authenticated in the notification center.

Fig. 20:

Authentication

5. Tap on the system message "Device authorization" in the notification center.
6. Then tap on the message.

– The dialogue "Authenticate device" opens.

Fig. 21:

Authenticating device

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands