Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 179 / 364

background image

KNX control elements and application parameters

"Display" control element

Product manual 2CKA001473B5342

│

179

10.13.13 Type of display element — Wind rose

Note

For option "Wind rose" of parameter "Type of display element" the same
supplementary parameters are available, such as for option "Linear
measurement display", Chapter 10.13.9 “Type of display element — Linear
measurement display — Measurement display with colour display“ on page 176.
Parameter "Measurement display with colour display" is not available.

10.13.14 Type of display element — Wind rose — Display value in control element

Options:

Deactivated

Activated

The parameter is used to specify whether the value of the selected element is displayed in the
display element.

–

Deactivated

: No display. No additional parameters available.

–

Activated

: The following supplementary parameters are displayed:

Unit

:

Options:

<Text>

The parameter is used to enter the unit or the unit sign with which the measured value is
displayed in the display element.

The length of the text is limited to 60 characters.

Notice

Display the "Value of wind force" parameter when activating the parameter

– Only the following units are available for the selection of the parameter "Display value of

wind force":

Unit - Parameter "Display value of wind force"

:

Options:

m/s

Bft

km/h

Decimal places

:

Options:

Setting option from 0 - 2

The parameter is used to specify the number of decimal places of the displayed measured
value.

The number is limited to 2 places.

Thousands separator

:

Options:

Deactivated

Activated

The parameter is used to specify whether a thousands separator is displayed in the
measured value.

«
...
177
178
179
180
181
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: AMX Pages: 1

PACK ELITE+ Series

Brand: XUNZEL Pages: 24

TV Aventos 3781 ZW

Brand: Loewe Pages: 24

kontron FlatView HYG

Brand: S&T Pages: 35

CP6207 0020 Series

Brand: Beckhoff Pages: 25

Brand: Conergy Pages: 9

Brand: Haier Pages: 1

Brand: Haier Pages: 53

Brand: Haier Pages: 27

Brand: Haier Pages: 16

Brand: Haier Pages: 47

Brand: Haier Pages: 47

Brand: Haier Pages: 19

Brand: Haier Pages: 47

Brand: Haier Pages: 110

Brand: Haier Pages: 66

Brand: Haier Pages: 64

Brand: Haier Pages: 197

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands