Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 232 / 364

background image

KNX control elements and application parameters

Application "Internal RTC"

Product manual 2CKA001473B5342

│

232

Fan coil:

■

Fan coil 4°C 90 min

■

Free

configuration

Multiple heating types (panel heating, convector heating or fan coil) with preset parameters are
available to the user.

– If the required heating type is not available, individual parameters can be specified in free

configuration.

Note

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%", "PI PWM, On/Off“ or "Fan coil".

10.24.5 Heating control — P-component

Options:

Setting option between 1 - 20

The P-component stands for the proportional range in a control. It fluctuates around the setpoint
value and can be used to influence the control speed of a PI controller. The smaller the value
set, the faster the control reacts. However, the value should not be set too small because
otherwise there may be a risk of an overshoot. A P-component from 0.1 to 2 K can be set.

Notice

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%,"PI PWM, On/Off“ or "Fan coil". In addition,
the "Heating type" parameter must be set on "Free configuration".

10.24.6 Heating control — I-component

Options:

Setting option between 0 - 600

The I-component refers to the readjust time of a control. The integral component has the effect
of moving the room temperature slowly toward, and ultimately reaching, the setpoint value.
Depending on the type of system used, the reset time has to have different values. In general,
the more inactive the overall system, the greater the readjust time.

Notice

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%,"PI PWM, On/Off“ or "Fan coil". In addition,
the "Heating type" parameter must be set on "Free configuration".

10.24.7 Heating control — Extended settings

Options:

Deactivated

Activated

– This parameter enables additional functions and communication objects, e.g. "Basic stage

heating".

«
...
230
231
232
233
234
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

VIO-100/PC100 Series

Brand: Premio Pages: 107

i3TOUCH E1055 4K

Brand: i3-TECHNOLOGIES Pages: 20

Brand: Palsonic Pages: 36

Brand: VAVIS Pages: 4

Brand: Uniflair Pages: 76

BRAVIA 4-160-344-11(1)

Brand: Sony Pages: 35

UN46B8000 - 46" LCD TV

Brand: Samsung Pages: 2

Brand: Samsung Pages: 1

Brand: Samsung Pages: 1

UN32B6000 - 32" LCD TV

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands