Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 136 / 364

background image

KNX control elements and application parameters

Operation of "RGBW" control element“

Product manual 2CKA001473B5342

│

136

Activated

An additional 1-bit communication object "Switch status" is enabled via the parameter.

When the object has been enabled, the status display of the control element indicates the
current status of the object. The feedback object can ensure that the correct status is always
displayed.

If an actuator has a separate feedback object, this additional object can check whether the
actuator has switched. For this the feedback object of the actuator must be connected with the
feedback object of the button via a common group address (Action).

If the status display is not activated via a feedback object, the control element always changes
to the other status when actuated.

10.5.10 Enable 1-bit communication object "Disable"

Options:

Deactivated

Activated

There is the option of temporarily disabling the function via an additional communication object
"Disable".

«
...
134
135
136
137
138
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: IAI Pages: 4

VBHNxxxSJ25 series

Brand: Panasonic Pages: 13

Brand: Renogy Pages: 20

Brand: Displays2go Pages: 24

VIPA HMI PPC021 ES

Brand: YASKAWA Pages: 57

Brand: AXIOMTEK Pages: 66

Brand: Terasic Pages: 39

Brand: Sunforce Pages: 1

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 34

Brand: Curtis Pages: 1

Twin Coil Sealed Solar System

Brand: Atmos Pages: 15

Brand: Cybernet Pages: 50

Brand: Viessman Pages: 16

Brand: Solon Pages: 38

Brand: sylber Pages: 12

Brand: sylber Pages: 16

Brand: Baxi Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands