Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 202 / 364

KNX control elements and application parameters

Application "Door communication"

Product manual 2CKA001473B5342

│

202

10.17 Application

"Door

communication"

10.17.1 Use of door communication

Options:

Deactivated

Activated

The parameter is used to specify whether an application page is displayed in the panel for the
door communication.

–

Deactivated

: No application page is displayed. No additional parameters available.

–

Activated

: An application page is displayed. The following supplementary parameters are

displayed:

Which

door communication system

Options:

Welcome

Welcome M

The parameter is used to specify which door communication system is used.

10.17.2 Page PIN-protected

Options:

Deactivated

Activated

The parameter is used to specify whether the application page for the door communication is
protected by a PIN code.

–

Deactivated

: The application page is not protected.

–

Activated

: The application page can only be called up by entering a PIN code. The following

supplementary parameter is available:

PIN code level

Options:

Level 1

Level 2

Level 3

The parameter is used to specify the PIN code level for the application page.

Notice

Details about the PIN code, see chapter “Basic settings (system settings)
of the panel“ on page 78.

10.17.3 Use of control elements [%]

Options:

Deactivated

Activated

The parameter is used to specify whether the control elements are used.

–

Deactivated

: No control elements are used. No additional parameters available.

–

Activated

: The following supplementary parameters are displayed:

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands