Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 28 / 364

Product Overview

Product manual 2CKA001473B5342

│

4.4

Overview of KNX functions

The following table provides an overview of the possible functions and applications of the
device:

Standard KNX functions

Applications

■

Switching

■

Dimming

■

Slide controller functions

■

Blind control

■

RGBW

operation

■

Fan control (step switch)

■

VRV operation

■

Split Unit operation

■

Scene

control

■

Display functions (display elements)

■

Room temperature controller (RTC)

■

Page link functions

■

Audio

control

■

Door communication

■

Fault and alarm messages

■

Scene

actuator

■

Presence

simulation

■

Time

programs

■

Logic

functions

■

Internal

RTC

Table 2: Overview of functions

4.5

Device overview

Device overview (front side)

Fig. 2:

Device overview Busch-SmartTouch

front side

Pos.

Description

[1]

Touch screen

[2]

Proximity and brightness sensor

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands