Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download

Page: 208 / 364

KNX control elements and application parameters

Application "Fault and alarm messages" - Settings of the individual messages

Product manual 2CKA001473B5342

│

208

Repeat of alarm as long as it is active

Options:

Deactivated

Activated

–

Deactivated

: In the active state the acoustic alarm signal is not repeated. No additional

parameters available.

–

Activated

: The signal tone is repeated as long as the alarm is active. The following

supplementary parameter is available:

Repeat time [min.]

Options:

Setting option from 1 - 60

The parameter is used to specify the cycle (in minutes) with which the alarm is repeated.

–

14 byte

: A text is displayed and sent when acknowledging the alarm. The following

supplementary parameters are available:

Sending text at acknowledgement

Options:

Deactivated

Activated

–

Deactivated

: No text is sent at acknowledgement. No additional parameters available.

–

Activated

: The text that was specified via the following parameters is sent at

acknowledgement:

Text at acknowledgement

Options:

<Text>

The parameter is used to specify the text that is sent at acknowledgement of the alarm.
The length of the text is limited to 60 characters.

Acoustic alarm signal

Options:

Deactivated

Activated

The parameter is used to specify whether the signal tone specified under the global settings
is played see chapter 10.18 “Application "Fault and alarm messages" - Global settings“ on
page 205.
–

Deactivated

: No acoustic alarm signal. No additional parameters available.

–

Activated

: The signal tone is played at an alarm signal. The following supplementary

parameter is available:

Duration of audio signal [min.]

Options:

Setting option from 1 - 60

The parameter is used to specify how long the specified signal tone is to be played (in
minutes).

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Product Manual

Search results

Summary of Contents for Busch-SmartTouch ST/A10.11-811

Reviews:

Related manuals for Busch-SmartTouch ST/A10.11-811

Brands by name

Popular brands