Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 175 / 364

background image

KNX control elements and application parameters

"Display" control element

Product manual 2CKA001473B5342

│

175

The parameter is used to specify the smallest value that is sent via telegrams to the display
element.

Any value within the limits specified by the object type and its value range can be entered.

Maximum object value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the largest value that is sent via telegrams to the display
element.

Any value within the limits specified by the object type and its value range can be entered.

Displayed minimum value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the smallest value that is displayed in the display element.

Any value within the limits specified by the object type and its value range can be entered. The
value can deviate from the setting of parameter "Minimum object value".

Displayed maximum value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the largest value that is displayed in the display element.

Any value within the limits specified by the object type and its value range can be entered. The
value can deviate from the setting of parameter "Maximum object value".

–

14-Byte value

:

14-Byte text

:

Options:

<Text>

«
...
173
174
175
176
177
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: Samsung Pages: 723

Brand: Crestron Pages: 16

Brand: FDI Pages: 11

Brand: CanadianSolar Pages: 22

Brand: Eiki Pages: 28

KS23 Trio Labstart

Brand: Duomo Pages: 4

Brand: DeDietrich Pages: 44

PPC-5152-D525-E

Brand: IEI Technology Pages: 132

Brand: IEI Technology Pages: 154

Brand: IEI Technology Pages: 163

762-5/8000-000 Series

Brand: WAGO Pages: 202

Brand: Magnavox Pages: 37

Brand: Olli Pages: 8

Brand: Excell Pages: 47

Brand: IEI Technology Pages: 141

Brand: IEI Technology Pages: 76

Rexroth IndraControl VSP 3 Series

Brand: Bosch Pages: 47

Brand: Bosch Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands