Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Product Manual Download | Manualshive

Page: 169 / 364

background image

KNX control elements and application parameters

Control element: "Value slider"

Product manual 2CKA001473B5342

│

169

Maximum object value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the largest value that is sent from the control element via
telegrams.

Any value within the limits specified by the object type and its value range can be entered.

Displayed minimum value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the smallest value displayed by the control element on the
control element.

Any value within the limits specified by the object type and its value range can be entered. The
value can deviate from the setting of parameter "Minimum object value".

Displayed maximum value

:

Options:

Setting option depends on the selected object type.

The parameter is used to specify the largest value displayed by the control element on the
control element.

Any value within the limits specified by the object type and its value range can be entered. The
value can deviate from the setting of parameter "Maximum object value".

10.12.8 Enable 1-bit communication object "Disable"

Options:

Deactivated

Activated

There is the option of temporarily disabling the function via an additional communication object
"Disable".

«
...
167
168
169
170
171
...
»

Summary of Contents for Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Reviews:

No comments

Related manuals for Busch-SmartTouch ST/A10.11-811

Brand: Regulus Pages: 28

Brand: ATEMPOWER Pages: 7

Brand: Avalue Technology Pages: 19

Brand: YASKAWA Pages: 49

Brand: ICOP Technology Pages: 46

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Philips Pages: 3

17-LCD HDTV MONITOR FLAT TV CRYSTAL CLEAR III 17PF9936

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 16

Brand: Philips Pages: 20

Brand: Philips Pages: 36

Brand: Philips Pages: 43

Brand: Philips Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands