Engine Management Module (EMM)
Diagnostic Software Functions
70
Dynamic Tests
Dynamic tests are performed with the outboard
running.
Ignition Test
This test momentarily disables the ignition and
fuel injection circuits to one cylinder. By dropping
one cylinder, RPM and running quality changes
can be observed. Refer to
Fuel Test
This test momentarily disables one fuel injector
circuit. By dropping one cylinder, RPM and run-
ning quality changes can be observed. Refer to
Prime Oil
This test is used to cycle the oil injection pump for
priming the oiling system. Perform this test with
outboard running to activate oil injection pump.
Oil Control Settings
Set Oil Type
The TC-W3 oil type setting is the standard setting
for all outboards. Set TC-W3 for:
•
Operation with all TC-W3 outboard oils includ-
ing
XD30, XD50, or XD100
•
Applications requiring maximum lubrication
•
Extreme applications (racing or harsh condi-
tions)
The
XD100
setting provides an option to run the
outboard at a reduced oil injection rate. This set-
ting REQUIRES the use of
Evinrude XD100
out-
board lubricant and is not recommended for all
applications.
Use the
XD100
setting for:
•
Conventional use (runabouts, cruisers)
•
Moderate applications
Powerhead Break-In
Use the diagnostic software to initiate break-in oil-
ing. Break-in is a predetermined oiling program
Dynamic Tests Screen
008570
NOTICE
Running an
Evinrude E-TEC
outboard on
other grades of oil while set to XD100 oil will
result in increased engine wear and short-
ened outboard life.
1.
Oil control setting
008571
1
Summary of Contents for EVINRUDE E-TEC BE225HGXABA
