Angelo Po FX Series Technical Manual Download Page 74

Page: 74 / 125

Copyright by Servizio Clienti ANGELO PO Spa

4.9. Gas conversion

All equipment is tested and adjusted to work with Natural gas (G20), where it is required to

use a propane gas, follow the instruction below:

1. Gas nozzle replacement: Unscrew the gas pipe (Photo 1), remove the Natural gas

(G20) nozzle and put in place the replacement nozzle (photo 2), then tighten the

pipe. The nozzle works also as seal.

The nozzle must be mounted as shown in photo 3.

Injectors

FX61G3

FX101G3

FX82G3

G20

Ø635 - 3147120

Ø605 - 3141800

Ø635 - 3147120

G31

Ø465 - 3141630

Ø485 - 3153010

Injectors

FX122G3

FX201G3

FX202G3

G20

Ø640 - 3147130

Ø615 - 3141820

G31

Ø500 - 3167720

Ø465 - 3141630

Ø480 - 3153000

2. Setting the type of gas on the display:

enter menu “Service” (Password:SAAP),

enter menu “Setup gas”(Password:SI74),

select the type of gas used from the menu “Type of gas”

3. Perform analysis of flue gas (see section 4.6)

PICTURE 1

PICTURE 2

PICTURE 3

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands