Angelo Po FX Series Technical Manual Download Page 58

Page: 58 / 125

Copyright by Servizio Clienti ANGELO PO Spa

and Check the fan speed less then 500rpm. If alarm

then set STEP 7. If no alarm then step 0 = Standby is

selected.

OFF

LOCKOUT: the burner is locked. Internal safety check

is performed. After 5 secs. if the alarm is recoverable

then Step 8 is selected. If not recoverable then alarm is

displayed and remain in this status.

OFF

UNLOCKABLE: ignition is locked until RESET.

OFF

RESET: RESET activated and pass to phase STANDBY

OFF

Ignition speed

OFF

POSTPURGE: always activated for about 13 secs. and

then it pass to STEP 6 = if Stop is selected or it pass to

STEP 4 if it needs to recycle

The combustion control board is controlled by the power board with the following

commands:

Burner ignition

Burner off

The combustion control board start with the state "0" STANDBY, and when the power

board requires turning on the burner, go to the state "5" OPERATIVE, once detected the

presence of the flame. All intermediate states are done. When in state "5", depending on

the need for power / temperature, the power board drive the combustion control board

which controls the blower speed. When the oven reaches the temperature, the burner turns

off and the combustion control board goes in state “10” = postpurge and then in step "6"

and then returns available in the state "0". If there is any alarm then step 7 and 8 are

selected.

If there are problems the board turn on state “7” or "8" ( Locked Steps ), showing alarm.

For example GAS: F4 can be reset from the panel.

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands