Angelo Po FX Series Technical Manual Download Page 57

Page: 57 / 125

Copyright by Servizio Clienti ANGELO PO Spa

4.3. Blower control board: logic operation

The logic of the Blower control board and Combustion control board offers several steps:

there are 11 steps as reported in the table below and each one of these corresponds to a

check / audit and controls to the blower and to the gas.

STEP

Blower fan

speed

Gas valve

Description

OFF

STANDBY: ignition not required

OFF

CONTROL: : ignition required, check blower fan speed

(lower than 500 rpm). As soon as the check is finished

it pass to step 2, other wise after 20” appears the

GAS:F24.

Ignition speed

OFF

START: blower fan start and the ignition speed has

been checked. As soon as the check is finished it pass

to step 3, other wise after 30” appears the alarm

GAS:F24.

Ignition speed

OFF

PURGING: the blower fan runs at the ignition speed,

then if there are no alarms, then pass to step 4.

Ignition speed

OFF/ON

IGNITION: The Blower control pcb set the Burner

Control Board to start phase. After a wait of 7 sec. at

the blower purging speed, then the Burner control pcb

opens Gas Valve and spread out the spark. If the flame

sensor recognize the flame then the Burner Control

pcb feedback it to Blower Control pcb, and STEP 5 is

selected.

Otherwise recycle: 7secs/3secs

7sec.Gas+Spark=OFF + 3sec.Gas+Spark =ON.

The max number of ignition attempts are 3.

If No flame was detected, then STEP 10 (postpurge) is

selected before set 6 and 7 and 8 Steps.

Target speed

WORKING: ignition done successfully. Blower Control

pcb set up required the blower speed and the power of

the burner. This step will remain until the power is

requestd and/or until an alarm occurs, then step 10 is

selected.

OFF

STOP: burner turned off. The blower is set to stop. The

blower control check for alarm from Burner Control

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands