Angelo Po FX Series Technical Manual Download Page 124

Page: 124 / 125

Copyright by Servizio Clienti ANGELO PO Spa

124

Alarm on

display

Problem (on

the manual)

Solution (on the

manual)

Note (on the

manual)

Note for Service

E14

Electronic circuit

board

diagnostics

tripped.

Inform the after-sales

service.

The oven’s

functions are

disabled so no

cooking

cycles can be

carried out.

PCB temperature probe failure.

Replace the power board or the CPU

board.

E14V = CPU

E14Q = power board

E19

The humidity

probe has failed.

Inform the after-sales

service.

The oven’s

functions are

enabled so

cooking

cycles can be

carried out.

Check the connector terminals on the

probe and on the power board.

E20

Configuration

error

Inform the after-sales

service.

The oven’s

functions are

disabled so no

cooking

cycles can be

carried out.

Found inconsistencies between the

type of oven and installed boards.

Verify the installed boards (display,

power board) and devices (inverter and

combustion control), verify their proper

connection on net cables and repeat

the configuration of the oven.

E21 – E26

Washing cycle

alarms

See chapter 5.4

E27

Gas test missed

See chapter 4.8 (alarm gas chart)

E28

Valve not

working

Press reset button

The oven’s

functions are

enabled so

cooking

cycles can be

carried out.

Washing

programs are

disabled.

Check the connector terminals on the

valve and on the power board.

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands