Angelo Po FX Series Technical Manual Download Page 35

Page: 35 / 125

Copyright by Servizio Clienti ANGELO PO Spa

CPU board (1a) included the display and keys with LED backlighting. It is connected to the

keyboard (1b) with two flat cables and to the power card (2) with a network cable (RJ45).

The power board (2) receives all the signals from the oven probes (PT1000 temperature

sensors, door micro switch, core probe, etc.) and controls all organs of the oven through

the appropriate relays. Communicates with the CPU card (1a), with the inverter (4) and the

combustion and fan control boards (3) (for gas model only) via RJ45 network cables.

If there is no communication between the power board and the CPU board or the

combustion control board the alarm E13 appears (communication failed error).

1-SW

Transformer PCB

2 outputs 12Vac to the PCB 2

and from this to the CPU 1a

2-FW

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands