Angelo Po FX Series Technical Manual Download Page 44

Page: 44 / 125

Copyright by Servizio Clienti ANGELO PO Spa

•

Modulation Transitional power: the system is able to control all the range of power

from minimum to maximum with the control of the rotation speed of the blower fan

by the power board. In this way the combustion is "good" at any range of power.

•

Minimum power: The minimum power is set at 30-40% of maximum. In this case,

the vacuum created by the blower decreases and the effect of the valve offset

adjusting becomes more important. The proper adjustment of the valve is essential.

For details concerning the valve adjustment, see the section 4.4.3. Valve offset

adjusting.

* With the PLUS function turned off the oven works with maximum set at 90% of maximum

power, to use 100% of the power it is necessary to enable the PLUS function.

NOTE:

- The burner ignition occurs at a power of about 10% higher than the minimum (40-50%).

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands