Angelo Po FX Series Technical Manual Download Page 98

Page: 98 / 125

Copyright by Servizio Clienti ANGELO PO Spa

7.5. Component compartment cooling system

Cleaning and parts of the component compartment cooling system and air intake slots:

1. cooling fan of the display board (picture 1) always ON even when the oven is in

stand-by.;

2. cooling fan of the component compartment (picture 2) always ON even when the

oven is in stand-by.;

3. air intake slots into the component compartment (picture 3);

4. air box connected to the air intake slots into the component compartment (picture 4),

cleaning recommended;

5. air intake slots outside on the bottom of dashboard, cleaning recommended (picture

5);

6. air intake filter and air intake filter for gas valve (picture 6).

NOTE: If the cooling motor breaks the following alarm will appear: “components

compartment over temperature E10” (see chapter Alarms).

PICTURE 1

PICTURE 2

PICTURE 6

PICTURE 5

PICTURE 4

PICTURE 3

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands