Angelo Po FX Series Technical Manual Download Page 48

Page: 48 / 125

Copyright by Servizio Clienti ANGELO PO Spa

NOTE:

For any details concerning the valve adjustment, see the section 4.4.3. Valve offset

adjusting.

Be sure the air inlet filter (9) and the exit of the gas valve pressure test point pipe (6)

are totally clean (if necessary clean them properly).

ATTENTION!: Each replacing of the gas valve is necessary to make the wizard test

(see the section 4.4.1), check the combustion and even the gas valve offset adjusting.

4.2.2.

Mixer

NOTES:

Check that the combustion air filter is always clean and not clogged.

Check that the draft air tube is free of cuts or tears and that the clamps are tight

Check the connections tightness; do not use flames on gas burner because they

could be sucked into the mixing circuit and cause fire / explosion.

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands