Angelo Po FX Series Technical Manual Download Page 125

Page: 125 / 125

Copyright by Servizio Clienti ANGELO PO Spa

125

Alarm on

display

Problem (on

the manual)

Solution (on the

manual)

Note (on the

manual)

Note for Service

E29

Core probe not

inserted

Press reset button

The oven’s

functions are

enabled so

cooking

cycles can be

carried out.

---

E30 – E38

Electronic circuit

board

diagnostics

tripped.

Press reset button

If the problem

persists

inform the

after-sales

service.

Protections against electromagnetic

interferences. Check all the ground

wiring of the equipment. In case of gas

version, please check ignition electrode

and cover protections to be properly

fitted. Check all the wirings relative to

the ignition system. Check the correct

insulation of the cable.

E80 – E85

---

Inform the

after-sales

service.

---

Summary of Contents for FX Series






























































































































Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands

Angelo Po FX Series, Technical Manual

Search results

Summary of Contents for FX Series

Reviews:

Related manuals for FX Series

Brands by name

Popular brands