manualshive.com logo in svg

Angelo Po FX Series, Technical Manual

The Mitsubishi Electric FX Series Replacement Manual is a comprehensive user guide for FX Series products. This essential manual provides detailed instructions and troubleshooting tips for optimal performance. Easily download this manual for free from manualshive.com to ensure you have the necessary documentation for your Mitsubishi Electric FX Series product.

Share
Download
background image

 

Copyright by Servizio Clienti ANGELO PO Spa 

3 

4.11.

 

Periodic  gas flue analysis ................................................................................................................78

 

5.

 

WASHING CYCLES LEVELS 3...............................................................................................................79

 

5.1.

 

Washing circuit operating and components ......................................................................................79

 

5.2.

 

Clean test ..........................................................................................................................................82

 

5.3.

 

Washing Interruption .........................................................................................................................83

 

5.4.

 

Washing alarms table........................................................................................................................85

 

5.5.

 

Cleaning consumption table..............................................................................................................88

 

5.6.

 

Cleaning warning and cleaning blockage .........................................................................................89

 

5.7.

 

Warning descaling.............................................................................................................................91

 

6.

 

WASHING CYCLES LEVELS 2...............................................................................................................92

 

6.1.

 

Washing circuit operating and components ......................................................................................92

 

7.

 

DISMANTLE AND REASSEMBLY COMPONENTS ...............................................................................94

 

7.1.

 

Encoder .............................................................................................................................................94

 

7.2.

 

Motor .................................................................................................................................................95

 

7.3.

 

Door micro-switch .............................................................................................................................96

 

7.4.

 

Door glass frame disassembly ..........................................................................................................97

 

7.5.

 

Component compartment cooling system.........................................................................................98

 

7.6.

 

Door adjustment ................................................................................................................................99

 

7.7.

 

Core probe ......................................................................................................................................100

 

7.8.

 

Humidity probe ................................................................................................................................101

 

7.9.

 

Halogen lamp replacement .............................................................................................................102

 

7.10.

 

Lock dismantling .............................................................................................................................103

 

7.11.

 

Lock dismantling 20 trays models ...................................................................................................105

 

7.12.

 

Spark plug replacement ..................................................................................................................107

 

7.13.

 

Blower fan replacement ..................................................................................................................108

 

7.14.

 

CPU and display LCD boards (LIV.3) replacing .............................................................................109

 

7.15.

 

CPU and display LCD boards (LIV.3) replacing (2

nd

 version).........................................................115

 

7.16.

 

Roll-In adjustment RX201 - RX202.................................................................................................117

 

7.17.

 

Scheduled recommended maintenance .........................................................................................119

 

8.

 

ALARMS ................................................................................................................................................120

 

 

 

 

 

 

Summary of Contents for FX Series






























































































































Reviews:

No comments

Related manuals for FX Series

GE Built-in ovens Use And Care Manual preview
Built-in ovens
Brand: GE Pages: 44
G. Paniz FTG Series Instruction Manual preview
FTG Series
Brand: G. Paniz Pages: 22
Nectre Fireplaces N550 Operating Instructions Manual preview
N550
Brand: Nectre Fireplaces Pages: 7
Teka HLB 840 Installation & Maintenance preview
HLB 840
Brand: Teka Pages: 72
Welbilt MD180017LEU Instruction Manual preview
MD180017LEU
Brand: Welbilt Pages: 16
Daewoo KOG-311M Operating Instructions Manual preview
KOG-311M
Brand: Daewoo Pages: 19
Kuppersbusch EMWG 1050 Service Manual preview
EMWG 1050
Brand: Kuppersbusch Pages: 29
Jenn-Air JJW2827DS User Manual preview
JJW2827DS
Brand: Jenn-Air Pages: 40
Gaggenau GF 111 70 Installation Manual preview
GF 111 70
Brand: Gaggenau Pages: 12
AIRLUX AFGC310BK Use And Maintenance Manual preview
AFGC310BK
Brand: AIRLUX Pages: 82
Cafe CVM721 Owner'S Manual preview
CVM721
Brand: Cafe Pages: 52
Fama MTP100 Operating Manual preview
MTP100
Brand: Fama Pages: 16
Magic Chef MCD770RW Operation Instructions And Cooking Manual preview
MCD770RW
Brand: Magic Chef Pages: 18
Cuisinart TOB Instruction Booklet preview
TOB
Brand: Cuisinart Pages: 27
Belling BDO9608BK Instruction Manual preview
BDO9608BK
Brand: Belling Pages: 38
Kuppersbusch EEB 6500.8 Use And Installation Manual preview
EEB 6500.8
Brand: Kuppersbusch Pages: 96
Wolf PW422718 Planning Information preview
PW422718
Brand: Wolf Pages: 8
Sandstrom SCB2510E Instruction Manual preview
SCB2510E
Brand: Sandstrom Pages: 204

Brands by name

Popular brands

Load more brands