ACTi A713 Firmware Manual Download Page 86

Page: 86 / 115

Manual Mode

With this mode, users can select the suitable shutter speed, iris size and gain

value according to the environmental illumination. For Motorized Lens Models,

the shutter speed range is from 1/10000 to 1 sec. (NTSC) or from 1/10000 to

1/1.5 sec. (PAL). For other Models, the shutter speed range is from 1/10000 to 1

sec. (NTSC) or from 1/10000 to 1/1.5 sec. (PAL).

The range of the iris size is from 0 to 9, or select <Full open> to fully open the

iris. The gain value range is from 3dB to 48dB, or select <Off> to disable the

function.

NOTE:

The <Iris Size> setting is only available for models with Zoom

Lens.

NOTE:

The <Gain> setting is not available for Box Camera. Note that for

Motorized Lens models, the iris size setting differs. To set the iris size,

click on

, and the camera will auto detect the best iris size for the

environment. If necessary, users still can manually adjust the iris size by

selecting

and

. Alternatively, click on

to reset the iris

size. The iris size will be set to the largest. Then, users can manually

adjust the iris size by selecting

and

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands