manualshive.com logo in svg

ACTi A713, Firmware Manual, Page: 65 / 115

Share
Download
ACTi A713 Firmware Manual Download Page 65

 

64 

2.2.10    Recording 

The Recording setting can be found under this path: 

System> Recording

. 

 

In the <Recording> setting page, users can specify the recording schedule that 

fits the present surveillance requirement.   

 

 

Recording Storage 

Select a recording storage type, <SD Card> or <Network Share>. 

 

Enable Recording Schedule 

Two  types  of  schedule  mode  are  offered:  <Always>  and  <Only  during  time 

frame>.  Users  can  select  <Always>  to  activate  microSD/SD  card  or  Network 

Share Recording all the time. Or, select a set of schedule from the time frame 

blank, check specific weekdays and setup the start time (hour:minute) and time 

period (hour:minute) to activate the recording at certain time frames. The setting 

range for the duration time is from 00:00 to 168:59.  Please click on <Save> to 

save the setup. 

 

To delete a schedule, select one from the schedule list, and click <Delete>. 

Summary of Contents for A713




















































































































Reviews:

No comments