ACTi A713 Firmware Manual Download Page 75

Page: 75 / 115

If there are constant dynamic changes in the scene, it is suggested

just adjust <GOV Length> and disable <Dynamic GOV>.

Click on <Save> to confirm the setting.

Bitrate

⚫

8M Models (F/B/K/6)

The default setting of the H.265/H.264 bitrate for Stream 1 is 12288

kbit/s; for Stream 2 is 4096 kbit/s; for Stream 3/ Stream 4 is 2048 kbit/s.

The setting range is from 64 to 20480 kbps, and the total bit rate should

not exceed 51200 kbps.

⚫

Stitching Bullet Model (3)

The default setting of the H.265/H.264 bitrate for Stream 1 is 12288

kbit/s; for Stream 2 is 4096 kbit/s. The setting range is from 64 to 20480

kbps, and the total bit rate should not exceed 40960 kbps.

⚫

Fisheye Model (8)

The default setting of the H.265/H.264 bitrate for Stream 1/ Stream 2 is

4096 kbit/s. The setting range is from 64 to 20480 kbps, and the total bit

rate should not exceed 40960 kbps.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands