ACTi A713 Firmware Manual Download Page 42

Page: 42 / 115

frequency as the upload frame rate. The setting range is from 1 to 15

frames per second.

NOTE:

Make sure SMTP configuration has been completed.

Refer to section

Mail

for further details.

⚫

Send HTTP Notification

Check this item, select the destination HTTP address, and specify the

parameters for event notifications by <Motion Detection> triggered.

When an alarm is triggered, the notification can be sent to the specified

HTTP server.

For instance, if the custom parameter is set as

“

action=1&group=2

”, and

the HTTP server name is

“

http://192.168.0.100/admin.php

”, the

notification will be sent to HTTP server as

“

http://192.168.0.100/

admin.php/action=1&group=2

” when alarm is triggered.

⚫

Record Video Clip

Check this item and select a video recording storage type, <SD Card> or

<NAS> (Network-Attached Storage>. The Motion Detection recording

will be stored in microSD/SD card or the NAS when motion is detected.

Pre-trigger buffer recording function allows users to check what caused

the trigger. The pre-trigger buffer time range is from 1 sec. to 3 sec.

Select <Upload for __ sec> to set the recording duration after motion is

triggered. The setting range is from 1 to 99999 sec. Select <Upload

during the trigger active> to record the triggered video until the trigger is

off.

NOTE:

Please make sure the local recording (with microSD/SD

card) or the remote recording (with NAS) is activated so that this

function can be implemented. Refer to section

Recording

for

further details.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands