ACTi A713 Firmware Manual Download Page 54

Page: 54 / 115

<Pre-trigger buffer> function allows users to check what happened to

cause the trigger. The <Pre-trigger buffer> frame rate could be

pre-determined. On the other hand, <Post-trigger buffer> is for users to

upload certain amount of images after the alarm input is triggered.

NOTE:

<Pre-trigger buffer> generally ranges from 1 to 20 frames.

However, the range will change accordingly if the frame rate of

MJPEG on

Streaming>

Video Configuration

is 6 or smaller.

Check the box <Continue image upload> to upload the triggered images

during certain time or keep uploading until the trigger is off.

Select <Upload for __sec> and enter the duration in the blank.

The images of the duration will be uploaded to FTP when the alarm input

is triggered. The setting range is from 1 to 99999 sec. Select <Upload

during the trigger active> to make the images keep being uploaded to

FTP during the trigger active until the alarm is released. Set the Image

frequency as the upload frame rate. The setting range is from 1 to 15

frames per second.

NOTE:

Make sure the FTP configuration has been completed.

Refer to section

FTP

for further details.

⚫

Upload Image by E-Mail

Select this item and the administrator can assign an E-mail address and

configure various parameters. When the alarm is triggered,

event images will be sent to the appointed E-mail address. Note that to

implement this function, one of the streaming

MUST

be set as

MJPEG

;

otherwise, this function will be grayed out and cannot be accessed.

<Pre-trigger buffer> function allows users to check what happened to

cause the trigger. The <Pre-trigger buffer> frame rate could be

pre-determined. On the other hand, <Post-trigger buffer> is for users to

upload certain amount of images after alarm input is triggered.

NOTE:

<Pre-trigger buffer> generally ranges from 1 to 20 frames.

However, the range will change accordingly if the frame rate of

MJPEG on

Streaming> Video Configuration

is 6 or smaller.

Check the box <Continue image upload> to upload the triggered images

during certain time or keep uploading until the trigger is off.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands