ACTi A713 Firmware Manual Download Page 37

Page: 37 / 115

Select <Upload for __ sec> to set the recording duration after alarm is

triggered. The setting range is from 1 to 99999 sec. Select <Upload

during the trigger is active> to record the triggered video until the trigger

is off.

NOTE:

Please make sure the local recording (with microSD/SD

card) or the remote recording (with NAS) is activated so that this

function can be implemented. Refer to section

Recording

for

further details.

File Name

Enter a file name in the blank, e.g. image.jpg. The file name format of the

uploaded image can be set in this section. Please select the one that meets the

requirements.

⚫

Add date/time suffix

File name: imageYYMMDD_HHNNSS_XX.jpg

Y: Year, M: Month, D: Day

H: Hour, N: Minute, S: Second

X: Sequence Number

⚫

Add sequence number suffix (no maximum value)

File name: imageXXXXXXX.jpg

X: Sequence Number

⚫

Add sequence number suffix up to # and then start over

File Name: imageXX.jpg

X: Sequence Number

The file name suffix will end at the number being set. For example, if the
setting is up to “10”, the file name will start from 00, end at 10, and then

start all over again.

⚫

Overwrite

The original image in the FTP site will be overwritten by the new

uploaded file with a static filename.

Save

After completing all the settings mentioned above, please click on <Save> to

save all the settings in this page.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands