ACTi A713 Firmware Manual Download Page 64

Page: 64 / 115

Disk Cleanup Setting

Check <Enable automatic disk cleanup> and specify the time <1~999 day(s) or

1~142 week(s)> and storage limits <1~99% full> to configure disk cleanup

settings. Click on <Save> to confirm the settings.

Recording List

Each video file on the Network Share will be listed in the Recording list. The

maximum file size is 60 MB/per file.

When the recording mode is set as <Always> (consecutive recording) and the

NAS recording is also allowed to be enabled by events triggered, once events

occur, the system will immediately implement events recording to NAS. After the

recording of the events are finished, the camera will return to the regular

recording mode.

⚫

Remove

To remove a file, select the file first, and then click on <Remove>.

⚫

Sort

Click on

<Sort>, and the files in the Recording list will be listed in name

and date order.

The capital letter A / M / N / T / S / R / V / U in the very beginning of name

denotes the sort of the recording as below.

Initial

Recording Type

Initial

Recording Type

Alarm

Periodical Event

Motion

Regular Recording

Network Failure

Manual Trigger

Tampering

Audio Detection

⚫

Download

To open / download a video clip, select the file first, and then click on

<download> below the Recording list field. The selected file window will

pop up. Click on the AVI file to directly play the video in the player or

download it to a specified location.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands

ACTi A713, Firmware Manual

Search results

Summary of Contents for A713

Reviews:

Related manuals for A713

Brands by name

Popular brands