manualshive.com logo in svg

ACTi A713, Firmware Manual, Page: 107 / 115

Share
Download
ACTi A713 Firmware Manual Download Page 107

 

106 

2.6.3 

Auto Pan 

The Auto Pan Programming can be found under this path: 

PTZ> Auto Pan

. 

 

The camera supports 4 Auto Pan Paths. Please refer to the instructions below 

to set an Auto Pan Path. 

 

Auto Pan Setting 

Follow the steps to setup an Auto Pan Path. 

Step 1.

Select a path number from the drop-down list.   

Step 2.

Select the speed ratio from the <Speed> drop-down list; the speed ratio 

ranges from 0 (low) to 3 (fast).   

Step 3.

Choose  to  run  the  Auto  Pan  Path  in  right  /  left  direction  from  the 

<Direction> drop-down list. 

Step 4.

Move the cursor to the live view pane, and move the camera to a desired 

view as the Start Point of an Auto Pan Path.   

Step 5.

Click  the  <Set>  button  of  <Start  Point>  and  the  current  view  will  be 

automatically saved as the start point of the Auto Pan Path.   

Step 6.

Move  the  camera  to  another  desired  position  as  the  end  point  of  the 

Auto Pan Path.   

Step 7.

Click the <Set> button of <End Point> to save the setting. 

 

NOTE:

 The zoom ratio of an Auto Pan

’s Start Point remains the same 

throughout the path. 

 

Auto Pan Run 

Select  the  specified  Auto  Pan  Path  from  the  drop-down  list,  click  the  <Run> 

button, and then the camera will start moving horizontally as recorded.   

 

To view the camera panning in full screen mode, please move the cursor onto 

the  live  view  pane,  right-click  and  left-click  to  select 

“Fullscreen”.  Then  users 

can view the camera navigation in full screen. 

 

To stop running an Auto Pan Path, simply move the cursor to the live view pane 

and move the camera in any direction. 

 

Summary of Contents for A713




















































































































Reviews:

No comments