ACTi A713 Firmware Manual Download Page 55

Page: 55 / 115

Select <Upload for __sec> and enter the duration in the blank.

The images of the duration will be uploading by E-mail when the alarm

input is triggered. The setting range is from 1 to 99999 sec. Select

<Upload during the trigger active> to make the images keep being

uploaded to E-mail during the trigger active until the alarm is released.

Set the Image frequency as the upload frame rate. The setting range is

from 1 to 15 frames per second.

NOTE:

Make sure SMTP configuration has been completed.

Please refer to section

Mail

for further details.

⚫

Send HTTP notification

Check this item, select the destination HTTP address, and specify the

parameters for event notifications by <Alarm> triggered. When an alarm

is triggered, the notification can be sent to the specified HTTP server.

For instance, if the custom parameter is set as

“

action=1&group=2

”, and

the HTTP server name is

“

http://192.168.0.1/admin.php

”, the notification

will be sent to HTTP server as

“

http://192.168.0.1/admin.php?

action=1&group=2

” when alarm is triggered.

⚫

Record Video Clip

Check the item and select a video recording storage type, <SD Card> or

<NAS> (Network-Attached Storage). The alarm-triggered recording will

be saved into the microSD/SD card or the NAS.

Pre-trigger buffer recording function allows users to check what caused

the trigger. The pre-trigger buffer time range is from 1 to 3 sec. Select

<Upload for __ sec> to set the recording duration after alarm is triggered.

The setting range is from 1 to 99999 sec. Select <Upload during the

trigger active> to record the triggered video until the trigger is off.

NOTE:

Please make sure the local recording (with microSD/SD

card) or the remote recording (with NAS) is activated so that this

function can be

implemented. Refer to section

Recording

for

further details.

Summary of Contents for A713




















































































































Search results

Summary of Contents for A713

Reviews:

ACTi A713, Firmware Manual, Page: 55 / 115

Search results

Summary of Contents for A713

Reviews: