ABB IRB 6700I Page 455 Product Manual Download | Manualshive

Page: 455 / 730

background image

Note

Action

Follow the instructions given in the refer-
ence calibration routine on the FlexPendant
to create reference values.

If the robot is to be calibrated with refer-
ence calibration:

Find previous reference values for the axis
or create new reference values. These val-
ues are to be used after the repair proced-
ure is completed, for calibration of the ro-
bot.

Creating new values requires possibility to
move the robot.
Read more about reference calibration for
Axis Calibration in

Reference calibration

routine on page 684

.

If no previous reference values exist, and
no new reference values can be created,
then reference calibration is not possible.

If the robot is to be calibrated with fine
calibration:

Remove all external cable packages
(DressPack) and tools from the robot.

Removing the axis-1 motor

These procedures describe how to remove the motor.

Preparations before removing the axis-1 motor

Note

Action

Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.

1

Jog the robot to the synchronization posi-
tion.

2

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safe-
guarded space.

3

Disconnecting the motor cables

Note

Action

DANGER

Make sure that all supplies for electrical
power, hydraulic pressure, and air pressure
are turned off.

1

Continues on next page

Product manual - IRB 6700Inv

455

3HAC058254-001 Revision: L

© Copyright 2017 - 2020 ABB. All rights reserved.

4 Repair

4.7.1 Replacing the axis-1 motor

Continued

«
...
453
454
455
456
457
...
»

Summary of Contents for IRB 6700I



























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 6700I

Brand: Asus Pages: 13

Brand: Pro's Kit Pages: 40

Brand: artisan Pages: 106

Brand: Shini Pages: 142

Brand: Shini Pages: 147

JMHZ2-16D-X7400B-TM

Brand: SMC Networks Pages: 25

SoftHand2 Research

Brand: QB Robotics Pages: 48

Brand: Paddle Palace Pages: 13

Brand: Keenon Robotics Pages: 28

Brand: Hiwin Pages: 5

Brand: RD9 Solutions Pages: 15

Brand: RD9 Solutions Pages: 14

Brand: DST Robot Pages: 2

Brand: Arduino Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands