ABB IRB 6700I Page 207 Product Manual Download | Manualshive

Page: 207 / 730

background image

4.3.4 Lifting down the robot from inverted position

General

This section details how to lift down the robot from its inverted position, rotate it
and secure it floor mounted in order to perform service procedures that require
the robot to be standing on the floor.

DANGER

Always lock the position of the lower arm, using the yellow sleeve and
transportation lock screw, before attempting to lift the robot.

DANGER

Always keep the the transportation lock screw and sleeve in locked position
when the robot is floor standing. During some repair activities, the transportation
lock screw and sleeve is replaced with service stops. These situations are clearly
stated in the current repair activities in this manual.

Required tools and equipment

Note

Article number

Equipment

Contains fork lift pockets and all
required hardware for installation.
User instructions are enclosed
with the tool, see Directions for
use - Fork lift accessory for IRB
6700Inv.
In order to rotate the robot, either
use the turning tool or a fork lift
truck with a rotator attachment.

3HAC058825-001

Fork lift accessory set

User instructions are enclosed.

3HAC061162-001

Turning tool

Required documents

Document number

Document

3HAC060303

Directions for use - Fork lift accessory for IRB 6700Inv

-

User instructions for turning tool (enclosed with the
turning tool)

Removing the robot from inverted position

Use these procedures to lift down the robot from inverted position and rotate it to
floor standing.

Securing the lower arm

Use this procedure to secure the lower arm.

Note

Action

Jog axis 2 to -35°.

1

Continues on next page

Product manual - IRB 6700Inv

207

3HAC058254-001 Revision: L

© Copyright 2017 - 2020 ABB. All rights reserved.

4 Repair

4.3.4 Lifting down the robot from inverted position

«
...
205
206
207
208
209
...
»

Summary of Contents for IRB 6700I



























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 6700I

Brand: OKM Pages: 83

Brand: Haier Pages: 19

MODEL SPACE Robi

Brand: Deagostini Pages: 32

DJI RoboMaster AI Challenge AI Robot 2019

Brand: ICRA Pages: 30

Brand: PreCise Pages: 171

Brand: bionicbird Pages: 20

Brand: bionicbird Pages: 30

Brand: AgileX Pages: 39

Brand: SMC Networks Pages: 98

Brand: Kosmos Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands