ABB IRB 6700I Page 644 Product Manual Download | Manualshive

Page: 644 / 730

background image

Note

Article number

Equipment, etc

D=266.29x3.53

3HAB3772-145

O-ring

Used on gearbox.

Deciding calibration routine

Decide which calibration routine to be used, based on the information in the table.
Depending on which routine is chosen, action might be required prior to beginning
the repair work of the robot, see the table.

Note

Action

Decide which calibration routine to use for
calibrating the robot.

•

Reference calibration. External cable
packages (DressPack) and tools can
stay fitted on the robot.

•

Fine calibration. All external cable
packages (DressPack) and tools
must be removed from the robot.

1

Follow the instructions given in the refer-
ence calibration routine on the FlexPendant
to create reference values.

If the robot is to be calibrated with refer-
ence calibration:

Find previous reference values for the axis
or create new reference values. These val-
ues are to be used after the repair proced-
ure is completed, for calibration of the ro-
bot.

Creating new values requires possibility to
move the robot.
Read more about reference calibration for
Axis Calibration in

Reference calibration

routine on page 684

.

If no previous reference values exist, and
no new reference values can be created,
then reference calibration is not possible.

If the robot is to be calibrated with fine
calibration:

Remove all external cable packages
(DressPack) and tools from the robot.

Removing the axis-3 gearbox

Use these procedures to remove the axis-3 gearbox.

Preparations before removing the axis-3 gearbox

Note

Action

Decide which calibration routine to use,
and take actions accordingly prior to begin-
ning the repair procedure.

1

xx1700000450

Jog the robot to the position:

•

Axis-1: a position that allows best
possible access to fit the lifting ac-
cessories to the upper arm.

•

Axis-2: -35

•

Axis-3: -143 (so that the upper arm
is horizontal)

•

Axis-4: 0°

•

Axis-5: -90°

•

Axis-6: 0°

2

Continues on next page

644

Product manual - IRB 6700Inv

3HAC058254-001 Revision: L

© Copyright 2017 - 2020 ABB. All rights reserved.

4 Repair

4.8.4 Replacing the axis-3 gearbox

Continued

«
...
642
643
644
645
646
...
»

Summary of Contents for IRB 6700I



























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 6700I

Brand: RoboBuilder Pages: 28

Brand: SCHUNK Pages: 32

Brand: SCHUNK Pages: 44

Brand: HEBI Robotics Pages: 36

Hexapod R Series

Brand: HEBI Robotics Pages: 45

Brand: Aisoy Robotics Pages: 20

Brand: VARRAM Pages: 30

TIGER ELECTRONICS Robo-Chi Pets Series

Brand: Hasbro Pages: 2

Brand: Vex Robotics Pages: 23

Brand: Gear2Play Pages: 25

Brand: Universal Robots Pages: 12

Brand: Universal Robots Pages: 15

3PE Teach Pendant

Brand: Universal Robots Pages: 20

Brand: Universal Robots Pages: 249

Brand: Universal Robots Pages: 256

ProtoSnap MiniBot

Brand: sparkfun Pages: 16

Brand: sparkfun Pages: 39

Brand: Elektor Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands