Xerox DocuPrint N4525 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 89

Volume 1 / Print Engine - Error Codes & Messages

1

-

67

7

DRUM INSPECTION

Open the Left Upper Cover (A) and open the Drum
Shutter.

Are the stripper fingers damaged or is there
paper stuck under the fingers or stuck between
the Drum and Laser Print (EP) Cartridge
frame?

Replace the
Laser Print
(EP)
Cartridge

Go to step 8

8

DRUM ROTATION TEST

1. Open the Left Upper Cover and open the Drum

Shutter.

2. Hand rotate (counter clockwise) the Drum Drive Motor.

Does the Drum rotate smoothly and without
binding?

Go to step 9

Replace the
Laser Print
(EP)
Cartridge

9

PAPER TRAVEL INSPECTION

Open the Left Upper Cover, and observe the position of
the jammed paper.

Did the sheet of paper stop while exiting the
Fuser?

Go to step 10 Go to step 11

10

FUSER INSPECTION

1. Remove the three screws securing the Fuser Left

Cover and remove the Cover so you can observe the
Fuser Rolls.

2. Hand rotate (counter clockwise) the Main Drive Motor.

Does the Pressure Roller rotate smoothly and
are the Fuser Stripper Fingers undamaged?

Go to step 11 Replace the

Fuser
Assembly

11

PAPER TRAVEL INSPECTION

Remove the Fuser Cover (RRP 1-1) and observe the
position of the jammed paper.

Did the sheet of paper stop in the Offset Unit?

Go to step 12 Go to step 13

12

OFFSET UNIT INSPECTION

Check the Offset Unit for lodged scraps of paper or
damage.

Is the Offset Unit clean and undamaged?

Go to step 13 Clean or

replace the
Offset Unit
Assembly
(RRP 1-54)

13

FUSER EXIT SENSOR TEST

1. Enter Diagnostic Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / Fuser Exit Sen.

3. Press [4] to start, [0] to stop.
4. Insert, then remove, a sheet of paper into the Fuser

Exit Sensor.

Does the Control Panel display “with paper”
when you insert the paper into the Fuser Exit
Sensor, and is “without paper” displayed when
you remove the paper?

Go to step 14 Replace the

Fuser Exit
Sensor (PL
9.1)

14

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 15 Problem

solved

Table 1-47 Error Code E1-2 Paper Jam Clear Area A (cont'd.)

Step

Actions and Questions

Yes

No

«
...
87
88
89
90
91
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды