Xerox DocuPrint N4525 Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 231

Volume 1 / Print Engine - FRU RRPs

1

-

209

Removal

1.

Open the Left Lower Cover.

2.

Remove Rear Cover (RRP 5)

3.

Remove the machine screw securing the Feed In Chute to the Assembly, and
slide the Chute to the front of the Assembly to remove it.

4.

Remove the plastic Feed Chute from the Take-Away Roller.

Caution

Use extreme caution when removing the Feed Chute. It is easily

broken.

5.

Unhook and remove the spring from the Retard Support.

6.

Remove the machine screw securing the Bracket, then remove the Bracket.

7.

Remove the machine screw securing the Gear Stopper to the assembly.

8.

Remove the E-ring securing the Gear Stopper, then remove the Gear Stopper
from the shaft.

9.

Remove the E-ring securing Gear 22/20T to the shaft and remove the gear.

10.

Remove the E-ring securing Gear 22T to the shaft and remove the gear.

11.

Remove E-ring securing the plastic bearing and the Take-Away Roller Shaft to

the front of the printer frame. Then remove the Retard Assembly and attached
Take-Away Roller by moving it as far to the rear as possible, then swinging the
front end of the shaft to the right to clear the printer frame. Remove the
Take-Away Roller Assembly by sliding it out toward the front of the printer.

Note

When removing the Take-Away Roller Assembly, it may be
necessary to hold down the Stopper Link (see RRP 22, Figure 2)

while gently moving the assembly in various directions to find the
best position to get it out easily.

«
...
229
230
231
232
233
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды