manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 197

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

175

Press [2]  or [6] to 
display: 

ß

Press [3]  or [7] to 
display: 

ß

Turn -On
Duration

Comment

Finisher Unit
Shift Motor Rear

2 sec.

1. Press [4] to start test.
2. Actuates Shift Motor moving Shift Roller 

toward the Rear.

Finisher Unit
Shift Motor Frnt

2 sec.

1. Press [4] to start test.
2. Actuates Shift Motor moving Shift Roller 

toward the Front.

Finisher Unit
Jogging Motor F

2 sec.

1. Press [4] to start test.
2. Actuates the Jogging Motor Front for 

duration or Press [0] to stop.

Finisher Unit
Jogging Motor R

2 sec.

1. Press [4] to start test.
2. Actuates the Jogging Motor Rear for 

duration or Press [0] to stop.

Finisher Unit
Sheet Clamp Mot

2 sec.

1. Press [4] to start test.
2. Actuates the Sheet Clamp Motor in the 

Stacker Bin.

Finisher Unit
Trav Mot Front45

2 sec.

1. Extend Compiler Tray (tongue) to facilitate 

stapler movement.

2. Press [4] to start test.
3. Actuates the Traverse Motor, moving the 

Stapler to the front of the Finisher.
Note: All four Traverse Motor Tests result 
in similar movement, bringing the Stapler 
to the front of the Finisher.

Finisher Unit
Trav Mot Rear

2 sec.

1. Extend Compiler Tray (tongue) to facilitate 

stapler movement.

2. Press [4] to start test.
3. Actuates the Traverse Motor, moving the 

Stapler to the front of the Finisher.
Note: All four Traverse Motor Tests result 
in similar movement, bringing the Stapler 
to the front of the Finisher.

Finisher Unit
Trav Mot Rear45

2 sec.

1. Extend Compiler Tray (tongue) to facilitate 

stapler movement.

2. Press [4] to start test.
3. Actuates the Traverse Motor, moving the 

Stapler to the front of the Finisher.
Note: All four Traverse Motor Tests result 
in similar movement, bringing the Stapler 
to the front of the Finisher.

Finisher Unit
Trav Mot Front

2 sec.

1. Extend Compiler Tray (tongue) to facilitate 

stapler movement.

2. Press [4] to start test.
3. Actuates the Traverse Motor, moving the 

Stapler to the front of the Finisher.
Note: All four Traverse Motor Tests result 
in similar movement, bringing the Stapler 
to the front of the Finisher.

Finisher Unit
Swing Mot Frnt45

2 sec.

1. Extend Compiler Tray (tongue) to facilitate 

stapler movement.

2. Gently pull the Stapler to the front of the 

Finisher.

3. Press [4] to start test.
4. Actuates Stapler Swing Motor to swing 

Stapler  45

o

 to the front.

Table 1-107 Component Control Output

Press [1] or [5] to display: Main Menu

Comp Output Test

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды