Xerox DocuPrint N4525 Скачать руководство пользователя страница 260

Страница: 260 / 380

1-238

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-50 Toner Sensor (PL 7.2)

Removal

Remove the Rear Cover (RRP 1-5).

Disconnect P/J127 from the Input/Output Board.

Open the Left Upper Cover.

Remove the Laser Print (EP) Cartridge.

Remove the Flywheel Assembly (RRP 1-65)

Remove the Left Cover Interlock Switch (RRP 1-71)

Remove the Main Drive Assembly (RRP 1-66)

Use the flat blade of a screwdriver to pry up the front end of the Toner Sensor
(refer to the figure).

When the front end is freed, remove the Sensor along with the attached wire
harness.

Fig 1-73 Toner Sensor

S4525-121

(P/J127)

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды