Xerox DocuPrint N4525 Скачать руководство пользователя страница 6

Страница: 6 / 380

Service Safety Summary

For qualified service personnel only:

Refer also to the preceding Users Safety

Summary.

Do not service alone:

Do not perform internal service or adjustment of this

product unless another person capable of rendering first aid or resuscitation is

present.

Use care when servicing with power:

Dangerous voltages may exist at several

points in this product. To avoid personal injury, do not touch exposed

connections and components while power is on.

Disconnect power before removing the power supply shield, soldering or

replacing components.

Do not wear jewelry:

Remove jewelry prior to servicing. Rings, necklaces and

other metallic objects could come into contact with dangerous voltages and

currents.

Power source:

This product is intended to operate from a power source that will

not apply more then 250 volts rms between the supply conductors or between

wither supply conductor and ground. A protective ground connection by way of

the grounding conductor in the power cord is essential for safe operation.

This product is certified under IEC 825 as a Class 1 Laser Product.

CLASS 1 LASER PRODUCT

The DocuPrint

N4525 Network Laser Printer is certified to comply with Laser

Product Performance Standards set by the U.S. Department of Health and

Human Services as a Class 1 Laser Product. This means that this is a class of

laser product that does not emit hazardous laser radiation; this is possible only

because the laser beam is totally enclosed during all modes of customer

operation.

The laser and output of the laser scanner unit produces a beam that, if looked

into, could cause eye damage. Service procedures must be followed exactly as

written without change.

When servicing the machine or laser module, follow the procedures specified in

the manual and there will be no hazards from the laser.

Laser (FDA): Any laser label visible to service must be reproduced in the service

manual with location shown or indicated. Safe working procedures and clear

warnings concerning precautions to avoid possible exposure must also be

included.

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды