Xerox DocuPrint N4525 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 88

1-

66

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-19

Error Code E1-2

Paper Jam

Clear Area A

There is a paper jam between the Registration Sensor and the Fuser Exit Switch.

Logic Control on the Print Engine Controller Board sensed the Fuser Exit Sensor was

not actuated within the specified time since the Registration Clutch was actuated.

Table 1-47 Error Code E1-2 Paper Jam Clear Area A

Step

Actions and Questions

Yes

No

1

PAPER PATH INSPECTION

Inspect the paper path for paper scraps that may cause a
paper jam.

Is the paper path free of paper scraps?

Go to step 2

Clear the
paper path

2

PAPER INSPECTION

Inspect the paper that is loaded in the paper tray.

Is the paper loaded in the cassette wrinkled or
damaged?

Replace the
paper with
new paper

Go to step 3

3

PAPER TRAVEL INSPECTION

Open the Left Upper Cover (A) and observe the position
of the jammed paper.

Did the sheet of paper stop at the Registration
Rolls?

Go to step 4

Go to step 5

4

REGISTRATION CLUTCH TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test / IOT

Unit / Reg. Clutch On to check the Registration Clutch
function.

3. Press [4] to start, the Registration Clutch will actuate

for 2 seconds and release.

Does the Registration Roller clutch Actuate
when you start the test?

Clean the
Registration
Rollers or
replace the
Left Upper
Cover (A)
Assembly
(RRP 1-42)

Replace the
Registration
Clutch (RRP
1-41)

5

REGISTRATION SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / Reg. Sensor.

3. Press [4] to start, [0] to stop.
4. Open Left Upper Cover (A) and insert, then remove, a

sheet of paper into the Registration Sensor.

Does the Control Panel display “with paper”
when you insert the paper into the Registration
Sensor, and is “without paper” displayed when
you remove the paper?

Go to step 6

Replace the
Registration
Sensor

6

PAPER TRAVEL INSPECTION

Open the Left Upper Cover (A) and observe the position
of the jammed paper.

Did the sheet of paper stop on the Drum?

Go to step 7

Go to step 9

«
...
86
87
88
89
90
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды