manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 171

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

149

Diagnostics, Test 

Prints, Service Tests 

and NVRAM 

Adjustments

The printer has four modes of operation:

On-Line Mode

Power Saver Mode

Diagnostic Mode

Menu Mode.

On-Line Mode

On-Line is the printer’s normal operating mode.  In this mode, the printer is On-Line, 

under the control of the System Controller Board, and ready to generate output. The 
On-Line Mode occurs automatically when the printer is powered ON.

If the printer goes out of the On-Line Mode during operation, it may be restored to 

On-Line by pressing the On-Line button [0] on the Control Panel.

When the printer is On-Line, the “On Line” LED is illuminated steadily, indicating data 
reception, transmission, analysis and printing are allowed.  When the “On Line” LED is 

blinking, the printer is receiving or processing data, or printing.  

Power Saver

The printer employs a Power Saver Mode to reduce power consumption by lowering the 
temperature of the fuser.  If no data is received, or no Control Panel operation is 

performed, within a period of time (either printer default or set by the user) the printer 
enters the power saving state.

The Power Saver Mode interval can be set from the System Menu (in Menu Mode) and 

can be preset to Off, 15, 30, 60, 90, 120 or 180 minutes.

When the printer is in the power saving state, it takes longer to start printing the first page 

because it takes some time to raise the fuser temperature.

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды