manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 245

Volume 1 / Print Engine - FRU RRPs

1

-

223

Removal

1.

Remove the Multi-sheet Bypass Feeder Feed Clutch (RRP 1-29).

2.

Remove Multi-sheet Bypass Feeder Feed Roller (RRP 1-30).

3.

Remove the E-ring securing the Multi-sheet Bypass Feeder Front Feed 
Bearing to the Feed Shaft, and remove the Bearing.

Warning

Before performing Step (4) below, take note of the Feed Spring 

and its positioning before sliding out the Feed Shaft.  Take care to 

prevent the spring from releasing suddenly, which could result in 

it flying and causing injury.

4.

Slide the Feed Shaft out of the Pick Roller Assembly, and remove the Assembly 
from the Multi-sheet Bypass Feeder frame.

5.

Remove the Front and Rear Feed Bearings from the Pick Roller Assembly.

Replacement

1.

Reinstall the Front and Rear Feed Bearings onto the Pick Roller Assembly (see 
the figure for correct placement).

2.

Hook one end of the Feed Spring over the Pick Roller Assembly frame.

3.

Reinstall the Pick Roller Assembly into the Multi-sheet Bypass Feeder 
Assembly.

4.

Hold the Feed Gear in place, with the flat side against the Pick Roller 
Assembly.

5.

Slide the Feed Shaft through the Feed Gear, through the Rear Feed Bearing, 
through the Pick Roller Assembly, through the Feed Spring, through the Front 
Multi-sheet Bypass Feeder Bearing, and out through the cutout for the Front 
Feed Bearing.

6.

Slip the Front Feed Bearing over the end of the Feed Shaft, and slide the 
Bearing into the cutout in the frame.

7.

Continue sliding the Feed Shaft as far as it will go.

8.

Use the E-ring (removed in Step 3 above) to secure the Shaft to the Front Feed 
Bearing.

9.

Hook the free end of the Feed Spring through the opening at the rear of the 
Assembly frame.

10.

Reinstall the Multi-sheet Bypass Feeder Feed Roller (RRP 1-30).

11.

Reinstall the Multi-sheet Bypass Feeder Feed Clutch (RRP 1-29).

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды