Xerox DocuPrint N4525 Скачать руководство пользователя страница 5

Страница: 5 / 380

Fuser Components

WARNING

This printer uses heat to fuse the toner image to a sheet of paper.

The Fuser Assembly is very hot. Switch off printer power and wait at least 30

minutes for the Fuser to cool before you attempt to service the Fuser Assembly or

adjacent components.

Safety Components:

Make sure covers and panel are in place and that all

interlock switches are all functioning correctly after you have completed a printer

service call. If you bypass, or cheat, an interlock switch during a service call, use

extreme caution when working on or around the printer.

Warning Labels:

Throughout the printer, warning labels are displayed on

potentially dangerous components. When you service the printer, check to make

certain that all warning labels are in place.

Most importantly, read and obey all posted warning labels.

WARNING

Turning the power off using the On/Off switch does not de-energize

the printer. You must remove the power cord to disconnect the

printer from the main power source. Keep the power cord accessible

for removal in case of an emergency.

Safety instructions:

Read all installation instructions carefully before you plug

the product into a power source.

Care of product:

Disconnect the power plug by pulling the plug, not the cord.

Disconnect the power plug if the power cord or plug is frayed or otherwise

damaged,

Or if any liquid or foreign material is spilled into the case,

Or if the printer is exposed to any excess moisture,

Or if the printer is dropped or damaged,

Or if you suspect that the product needs servicing or repair,

And whenever you clean the product.

Ground the product:

Plug the three-wire power cord (with grounding prong)

into grounded AC outlets only. If necessary, contact a licensed electrician to

install a properly grounded outlet.

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды