Xerox DocuPrint N4525 Скачать руководство пользователя страница 159

Страница: 159 / 380

Volume 1 / Print Engine - Troubleshooting

137

RAP 1-72

Skewed Image

PROBLEM

The image is either twisted on the page or is not parallel to the
sides of the page.

THE PRINTER DISPLAYS NO ERROR CODE

Fig 1-27 Skewed Image

Table 1-96 Skewed Image

Step

Actions and Questions

Yes

PAPER FEED INSPECTION

Are the paper trays installed correctly, and is
the paper correctly loaded into each cassette?

Go to step 2

Reload the
paper and
reinstall the
cassettes.

PAPER PATH INSPECTION

Inspect the paper path, between the feed Tray and the
exit Bin, for contamination or obstructions.

Is the paper path free of obstructions?

Go to step 3

Remove
obstructions
from the
paper path.

FEED, PICK, AND RETARD ROLLER
REPLACEMENT

Replace the Feed Roller, Pick Roller, and Retard Roller
for the Feeder having the skew problem.

Is the image still skewed?

Go to step 4

Problem
solved

REGISTRATION ROLLER REPLACEMENT

Replace the Registration Roller (RRP 1-45).

Is the image still skewed?

Go to step 5

Problem
solved

LASER PRINT (EP) CARTRIDGE
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Is the image still skewed?

Go to step 6

Problem
solved

S4525-18

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды