Xerox DocuPrint N4525 Скачать руководство пользователя страница 191

Страница: 191 / 380

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

169

Press [2] or [6] to
display:

Press [3] or [7] to
display:

Action To Take

Displayed Result

Comp Input Test
MBF/ENV Unit

MBF/ENV Unit
MBF Paper Sensor

1. Press [4] to begin test.
2. Insert a sheet of paper into

the MBF.

3. Press [0] to end test.

Without Paper
With Paper

MBF/ENV Unit
Env Paper Sensor

1. Press [4] to begin test.
2. Insert an envelope into the

Envelope Feeder.

3. Press [0] to end test.

Without Paper
With Paper

MBF/ENV Unit
Env Feed Out Sen

1. Press [4] to begin test.
2. Insert a folded paper into the

right side of the paper path.

3. Press [0] to end test.

Without Paper
With Paper

Comp Input Test
Finisher Unit

Finisher Unit
Input Path Sen.

1. Press [4] to begin test.
2. Actuate Input Path Sensor.
3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Path Sensor

1. Press [4] to begin test.
2. Actuate Path Sensor.
3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Exit Path Sen.

1. Press [4] to begin test.
2. Actuate Exit Path Sensor.
3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Compile Exit

1. Press [4] to begin test.
2. Actuate Compile Exit

Sensor.

3. Press [0] to end test.

Without Paper
With Paper

Finisher Unit
Exit Rol Open HP

1. Press [4] to begin test.
2. Actuate Exit Roller Open HP

Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Sht Rol HP Front

1. Press [4] to begin test.
2. Actuate Sheet Roller Home

Position Front Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Jogger HP Front

1. Press [4] to begin test.
2. Actuate Jogger Home

Position Front Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Jogger HP Rear

1. Press [4] to begin test.
2. Actuate Jogger Home

Position Rear Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Stpl Traverse HP

1. Press [4] to begin test.
2. Actuate Staple Traverse

Home Position Sensor.

3. Press [0] to end test.

Not Home
Home

Finisher Unit

Stpl Swing Sen 1

1. Press [4] to begin test.
2. Actuate Staple Swing

Sensor 1.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Stpl Swing Sen 2

1. Press [4] to begin test.
2. Actuate Staple Swing

Sensor 2.

3. Press [0] to end test.

Not Home
Home

Finisher Unit
Compile Tr Paper

1. Press [4] to begin test.
2. Actuate Compile Tr Paper

Sensor.

3. Press [0] to end test.

Without Paper
With Paper

Table 1-106 Component Control Input Tests

Press [1] or [5] until to display:

Main Menu
Comp Input Test (cont'd.)

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды