Xerox DocuPrint N4525 Скачать руководство пользователя страница 164

Страница: 164 / 380

1-142

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-75

Repetitive Marks on Each Page

PROBLEM

Identical image defects appear on each or on every other
printed sheet.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-30 Repetitive Marks on Each Page

Table 1-99 Repetitive Marks on Each Page

Step

Actions and Questions

Yes

DRUM IMAGE INSPECTION

1. Generate a single Test Print.
2. Open the Upper Left Cover when the sheet of paper is

approximately half-way through the transfer process.

3. Carefully remove the Laser Print (EP) Cartridge from

the printer.

4. Inspect the surface of the Drum.

Does the mark appear on the Drum before
image transfer?

Replace the
Laser Print
(EP)
Cartridge

Go to step 2

TRANSFER IMAGE INSPECTION

Inspect the Test Print generated in step 1.

Does the mark appear on the paper after image
transfer?

Replace the
Bias Transfer
Roller
Assembly

Go to step 3

FUSED IMAGE INSPECTION

1. Generate a single Test Print.
2. Open the Upper Left Cover when the sheet of paper is

approximately half-way through the Fuser.

3. Inspect the Test Print.

Does the mark appear on the paper after
Fusing?

Replace the
Fuser
Assembly

S4525-21

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды