manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 53

Volume 1 / Print Engine - Error Codes & Messages

1

-

31

The Repair Analysis Procedure Table

If you used the Service Flowchart, it may have directed you to this section.  Follow the 

Repair Analysis Procedure Table

 located in this section

 

to help you analyze your printer 

problem.

How to Use a Repair Analysis Procedure Table

1.

If you have an error code or error message displayed, refer to the Repair 
Analysis Procedure in this section and locate the ERROR CODE in the “Error 
Code” column or the “Error Message” in the “

Displayed Error Message”

 

column, then go to the Repair Analysis Procedure indicated in the “

Go To...”

 

cell to the right of the ERROR CODE.  

2.

If you have a printer operation problem; go to the 

PRINTER PERFORMANCE

 

area in the Troubleshooting Section of this manual.

3.

If you have an print image problem; go to the

 IMAGE QUALITY

 area in the 

Troubleshooting section of this manual.

4.

Follow the Repair Analysis Procedure Table  leading from the “Problem” cell to 
the individual Primary Repair Analysis Procedure that corresponds to your 
error code, printer operation problem, or print image problem.

5.

Follow the instructions presented in the Repair Analysis Procedure.

6.

If the Repair Analysis Procedure instructs you to perform a diagnostic test, 
refer to Diagnostics area in the Tests and Adjustments Section of this manual.  

7.

Voltage and resistance values presented in the Repair Analysis Procedures are 
an approximation.  Actual readings may vary from the stated values.

8.

Primary Repair Analysis Procedures may direct you to a Secondary Repair 
Analysis Procedure.  

How to Follow a Repair Analysis Procedure

 

(See the sample Repair Analysis Procedure step below)

1.

Each numbered step in a Repair Analysis Procedure instructs you to perform a 
certain action or procedure.

2.

The 

Actions and Questions

 box may contain additional information and 

numbered procedure steps you must follow to perform the action.

3.

The action is followed by a question.

4.

If your response to the question is 

Yes

, then follow the instructions for a Yes 

reply.

5.

If your response to the question is 

No

, then follow the instructions for a No 

reply.

6.

Repair Analysis Procedures may ask you to take voltage readings at certain 
test points within the printer.  The

 Plug/Jack Connector Locations 

and

 Master 

Wiring Diagram sections of this manual 

contain information on test point 

locations and signal names.

7.

Repair Analysis Procedures may ask you to run a specific diagnostic routine in 
order to test a component or circuit.  The 

Tests /Adjustments

 and 

Resetting 

NVRAM

 sections of this

 

manual

 

contain information on printer diagnostics.

8.

Repair Analysis Procedures often ask you to replace a printer component.  The 
Key FRU (Field Replaceable Unit) section of this manual provides detailed 
steps for removing and replacing all major parts of the printer.  If the 
component is not part of the base engine, the Repair Analysis Procedure 
indicates which technical manual contains the procedure.

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды