Xerox DocuPrint N4525 Скачать руководство пользователя страница 270

Страница: 270 / 380

1-248

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-60 Lower Chute Assembly (PL 9.1)

Removal

Remove the Offset Roller Assembly (RRP 1-59).

Remove the five black machine screws securing the Lower Chute to the Exit
Assembly frame, and separate the Lower Chute from the frame.

Release P/J104 wire harness from the harness clips.

Squeeze the latches to unlock the Fuser Exit Sensor, and remove the Sensor
from the Lower Chute.

Fig 1-82 Lower Chute Assembly

S4525-131

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды