Xerox DocuPrint N4525 Скачать руководство пользователя страница 135

Страница: 135 / 380

Volume 1 / Print Engine - Troubleshooting

113

Image Quality Problems

RAP 1-60

Light (Undertoned) Prints

PROBLEM

The overall image density is too light. The image may also be
unfused due to insufficient image density.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-15 Light (Undertoned) Prints

Table 1-84 Light (Undertoned) Prints

Step

Actions and Questions

Yes

PAPER INSPECTION

Inspect the paper that is loaded in the paper Bins.

Is the paper wrinkled, dimpled, or show any
sign of having a high moisture content?

Replace with
dry, newly
opened paper

Go to step 2

LASER PRINT (EP) CARTRIDGE
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Is the image density normal?

Problem
solved

Go to step 3

IMAGE DEVELOPMENT INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Grid Pattern Test Print and switch OFF

printer power halfway through the print cycle.

3. Open the Left Upper Cover.
4. Open the Drum Shutter by pressing in the interlock

plunger to the rear of the Laser Print Cartridge.

5. Hand rotate (counter clockwise) the Drum Drive Motor

flywheel to advance the Drum far enough so you can
see the developed image area on the Drum before it
reached Transfer.

Is the image on the drum completely
developed; with sharp, black, easily read
areas?

Go to step 4

Replace the
High Voltage
Power Supply
Assembly
(RRP 1-69)

S4525-06

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды