Xerox DocuPrint N4525 Скачать руководство пользователя страница 47

Страница: 47 / 380

Volume 1 / Print Engine - General Information

Custom paper sizes

Unacceptable media

The following media are unacceptable for use in the printer. Their use may cause high
rates of jamming and other paper-handling problems:

Excessively thick or thin paper

Heavily textured paper

Paper that has already been printed on (pre-printed letterhead is allowed)

Wrinkled, torn, or bent paper

Moist or wet paper

Curled paper

Paper with an electrostatic charge

Glued paper

Paper with special coating

Paper unable to withstand a temperature of 150

C (302

Thermal paper

Carbon paper

Universal transparencies

Paper with paper fasteners, ribbons, staples, tape, etc. attached

Label stock with exposed backing sheet.

Table 1-20 Custom Paper Sizes

Acceptable sizes

Custom paper tray

Multi-sheet Bypass Feeder

Width

181 - 298.5 mm
(7.13 - 11.75 in.)

76.2 - 297 mm
(3 - 11.69 in.)

Length
Tray 1
Trays 2 & 3

up to 431.8 mm
(up to 17 in.)
148 mm (5.83 in.) minimum
182 mm (7.16 in.) minimum

98.4 - 431.8 mm
(3.875 - 17 in.)

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды