Xerox DocuPrint N4525 Скачать руководство пользователя страница 199

Страница: 199 / 380

Volume 1 / Print Engine - Maintenance & Cleaning

177

Scheduled Maintenance

The DocuPrint N4525 is designed and tested to require little maintenance. A User

Maintenance Kit (P/N 109R00048 for 110 volt printer and 109R00049 for 220 volt
printers) contains:

Replacement Fuser

Bias Transfer Roller

Feed Rollers (15 ea. - three for each paper input Bin)

Rubber gloves for handling Feed and Bias Transfer rollers

Cleaning cloth.

The printer will tell the user when to install the User Maintenance Kit (300,000 prints).

Normally, it is not necessary for a trained technician to install the kit. Following
installation, it is necessary to reset the maintenance counter.

Note

See NVRAM Adjusments in the Diagnostics, Test Prints, Serivces

Tests and NVRAM Adjustments section of this manual for this
procedure.

Recommended Tools

Standard service tools used in printer repair

Toner vacuum, such as the 3M Toner Vac

Caution

Do NOT use a standad vacuum to clean up a toner spill.

Suction bulb to use as an air puff blower

Toner rags (specially treat fibrous paper cleaning “rags” that attract and pick up

toner and dust particles

Cotton swabs (for those hard to get at places)

Cleaning cloth

Isopropyl alcohol

Simple Green or equivalent cleaner

Maintenance and

Cleaning

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды