manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 239

Volume 1 / Print Engine - FRU RRPs

1

-

217

Removal

1.

Remove the Multi-sheet Bypass Feeder Assembly (RRP 1-25).

2.

Place the Multi-sheet Bypass Feeder upside down, with the Tray facing you.

3.

Remove the two self-tapping screws securing the Lower Cover to the Upper 
Cover.

4.

Locate the three latches on the right side of the Bin.

5.

Press the first latch while you pry the edge of the Lower Cover out and over the 
latch of the Upper Cover.

6.

Repeat step 5 for the remaining two latches located on the right side of the Bin.

7.

Repeat step 5 for the two latches that are located on the left side of the Bin, 
and remove the Lower Cover from the Upper Cover.

8.

Remove the Multi-sheet Bypass Feeder Bin.

9.

Squeeze together the latches holding the Multi-sheet Bypass Feeder Size 
Sensor to the Multi-sheet Bypass Feeder Side Guide, and pry the Sensor off 
and away from the Upper Cover.

10.

Disconnect P/J107 and remove the Sensor Assembly.

Replacement

1.

Reinstall the Multi-sheet Bypass Feeder Side Guide, making sure the two latch 
tabs at the bottom of the Guide fit through the cutout in the Upper Cover.

2.

Slide the Side Guide all the way to the right (toward the Multi-sheet Bypass 
Feeder Tray Spring).

3.

Hold the Side Guide in place while you press the two holes in the Size Sensor 
onto the two latch tabs

4.

Press hard enough so the Size Sensor locks (snaps) into place.

5.

Make sure the spring-loaded arm of the Sensor is under the molded track.

6.

Slide the Sensor Assembly to the left to make sure it moves smoothly and the 
spring-loaded arm lowers as you move the Sensor to the left, and raises when 
you move the Sensor to the right.

7.

Route the Sensor wire harness along the molded channel and through the 
cutout on the right side of the Upper Cover.

8.

Reconnect P/J107.

9.

Reinstall the Multi-sheet Bypass Feeder Bin, with the arrow side  down.

10.

Slide the three tabs on the upper edge of the Upper Cover into the three 

cutouts in Lower Cover, and press the Upper Cover onto the Lower Cover.

11.

Press at the five latch locations to make sure the latches have locked the 

Lower Cover in place.

12.

Use the two self-tapping screws (removed in Step 3 above) to secure the 

Lower Cover to the Upper Cover.

13.

Reinstall the Multi-sheet Bypass Feeder Assembly (RRP 1-25).

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды